NS0-183 Tested & Approved NetApp NCSIE ONTAP Study Materials
Validate your Skills with Updated NetApp NCSIE ONTAP Exam Questions & Answers and Test Engine
Network Appliance NS0-183 exam is intended for IT professionals who want to gain certification as a NetApp Storage Installation Engineer, ONTAP. NS0-183 exam is designed to test the candidate’s knowledge and skills in deploying and managing NetApp ONTAP storage solutions. NS0-183 exam is also aimed at professionals who have experience working with NetApp ONTAP storage solutions and are looking to enhance their skills and knowledge.
Network Appliance NS0-183 (NetApp Storage Installation Engineer, ONTAP) Certification Exam is a valuable certification program for professionals who work with NetApp storage systems. NetApp Storage Installation Engineer, ONTAP certification validates the candidate's skills and knowledge in the installation, configuration, and maintenance of NetApp storage systems, and demonstrates a deep understanding of the ONTAP software and hardware architecture, as well as network protocols. Certified professionals can use this certification to advance their careers and participate in the NetApp certification program.
To be eligible for the NS0-183 certification exam, candidates should have a solid understanding of storage fundamentals, including storage protocols, disk technologies, and RAID configurations. They should also have hands-on experience with NetApp storage systems, including configuring and managing storage systems using ONTAP software. Additionally, candidates should possess strong troubleshooting skills and be able to identify and resolve common storage-related issues.
NEW QUESTION # 15
A storage administrator is trying to upgrade a pair of FAS2520s with internal SATA storage to a new 2-node FAS8300 cluster. The storage administrator wants to preserve the existing data.
In this scenario, which two capabilities are available to the storage administrator? (Choose two.)
- A. the ability to move the volumes from the old nodes to the new nodes
- B. the ability to convert the FAS2520s to disk shelves and attach them to the new nodes
- C. the ability to pull out the tray of internal disks of the FAS2520s and reseat the tray in the internal storage of the FAS8300s
- D. the ability to create a 4-node MetroCluster across the four nodes
Answer: B,D
NEW QUESTION # 16
You use the system health subsystem show command to troubleshoot your newly installed ONTAP cluster.
In this scenario, which two health outputs would this command show you? (Choose two.)
- A. shelf connectivity
- B. cluster switch cabling
- C. node CPU utilization
- D. data switch cabling
Answer: A,C
Explanation:
Explanation/Reference: https://www.doc-developpement-durable.org/file/Projets-informatiques/cours-&-manuels- informatiques/Netapp/Data%20ONTAP%208.0%207-Mode%20System%20Administration%20Guide.pdf
NEW QUESTION # 17
Which statement regarding Epsilon is true?
- A. Epsilon is reassigned automatically to the HA partner in case the current owner of the epsilon suddenly reboots.
- B. The node holding the epsilon has extra fractional vote weight.
- C. The epsilon acts as a tiebreaker in a 2-node cluster.
- D. Whenever a new node is added, the epsilon is automatically reassigned to this node.
Answer: B
NEW QUESTION # 18
Click the Exhibit button.
As shown in the exhibit, you have an 8-node ONTAP 9.7 cluster. You are asked to set up a SnapMirror volume relationship between node-1 and node-8 in the same cluster.
In this scenario, which two network components are used by the SnapMirror volume? (Choose two.)
- A. cluster LIFs
- B. private network
- C. management LIFs
- D. client network
Answer: A,B
NEW QUESTION # 19
You are completing an ONTAP base installation, and your customer is asking you to create two SVMs, one for NFS and one for SMB.
Which type of SVM needs to be created to complete the installation?
- A. system SVM
- B. multitenancy node SVM
- C. admin SVM
- D. data SVM
Answer: D
NEW QUESTION # 20
Which two commands verify that AutoSupport is working as expected?
- A. autosupport show
- B. autosupport test show
- C. autosupport history show
- D. autosupport check show
Answer: C,D
NEW QUESTION # 21
While installing new Cisco cluster switches, you need to download the appropriate RCF to the switch.
In this scenario, which two file transfer protocols would be used? (Choose two.)
- A. FTP
- B. NFS
- C. HTTP
- D. SCP
Answer: A,C
NEW QUESTION # 22
Which two SVMs are automatically created during the cluster setup? (Choose two.)
- A. system SVM
- B. admin SVM
- C. data SVM
- D. node SVM
Answer: A,B
NEW QUESTION # 23
You want to ensure the highest path resilience and performance increase to the storage stack on your FAS8700 cluster.
In this scenario, which two types of stack cabling are available to use? (Choose two.)
- A. mixed-mode
- B. single path
- C. quadpath HA
- D. multipath HA
Answer: C,D
NEW QUESTION # 24
According to NetApp best practices, how many NTP servers should you associate with an ONTAP cluster?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: C
NEW QUESTION # 25
A customer has a current AFF ASA A700 cluster and they want to expand the cluster by adding a second AFF ASA A700 HA pair.
In this scenario, which step would be required to accomplish this task?
- A. Install a Brocade FC switch and create zoning between the original cluster and the new cluster.
- B. Install a BES-53248 cluster switch and convert the AFF ASA A700 from a switchless to switch cluster.
- C. The customer will need to create a separate cluster for the second AFF ASA A700 pair.
- D. Enable ALUA between the two HA pairs to allow cluster backend traffic.
Answer: C
Explanation:
With Ontap 9.7 ASA can only be a stand alone HA cluster. With Ontap 9.8 (not part of this exam) the cluster can be expanded to 12 nodes The following text is part of the TR4515, page 6 With ONTAP 9.7, NetApp introduced AFF ASA systems, which feature symmetric active-active topology, as shown in Figure 2. The ASA supports SAN (block protocols) only and is built on a single HA pair. It currently supports FC and iSCSI protocols, and support for NVMe protocols and larger clusters are expected in later releases.
NEW QUESTION # 26
An ONTAP cluster is installed at a secure site. The array has no access to the Internet but is managed 24/7 by onsite engineers. The customer requires that when hardware failures occur, the failures are reported to the NetApp Support team as quickly as possible.
In this scenario, which two tasks should be performed during the project hand-off procedure to satisfy the customer's requirement? (Choose two.)
- A. Ensure that the onsite engineers receive EMS alerts when hardware issues occur.
- B. Educate the onsite engineer about how to manually log support calls.
- C. Educate the onsite engineers about invoking the AutoSupport tool from ONTAP System Manager.
- D. Ensure that Active IQ Config Advisor is installed.
Answer: A,C
NEW QUESTION # 27
Click the Exhibit button.
You are installing a 2-node AFF A400 switchless cluster. You have cabled the management network to the e0M port. NetApp also recommends cabling to a redundant management network switch.
Referring to the exhibit, to which port should the redundant management network be cabled?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: A
NEW QUESTION # 28
You create a LIF called svm_cifs_lif01 on a port that is already in an up state. After you test the storage failover, the LIF does not automatically revert to its home port.
In this scenario, what should you do to solve the problem?
- A. Configure the LIF with the DHCP option.
- B. Configure a new failover group.
- C. Add the port in a broadcast domain.
- D. Configure the LIF with the automatic revert option.
Answer: D
NEW QUESTION # 29
Which LIF type is used by default for hardware-assisted storage failover communication?
- A. node-mgmt
- B. data
- C. intercluster
- D. cluster-mgmt
Answer: A
NEW QUESTION # 30
In ONTAP 9.7 software, how many different replicated databases (RDBs) exist per node?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: A
Explanation:
Explanation/Reference: https://www.storagefreak.net/2017/08/netapp-cdot-ontap-9-rdb-and-cluster-replication-ring
NEW QUESTION # 31
You installed a new AFF A800 2-node ONTAP 9.5 cluster and are asked to run diagnostics to validate the hardware.
Which command is used from the loader prompt to enter diagnostics?
- A. boot_diags
- B. printenv
- C. sldiag
- D. savenv
Answer: A
NEW QUESTION # 32
You are cabling two Cisco 3232C switches for the cluster interconnect of a 4-node AFF A800 cluster.
Which pair of ports are used to cable the Inter-Switch Link (ISL) between the switches?
- A. 0/1 and 0/2
- B. 0/13 to 0/16
- C. 1/21 to 1/24
- D. 1/31 and 1/32
Answer: D
NEW QUESTION # 33
You configured AutoSupport and are trying to send a full AutoSupport message to NetApp.
You use the autosupport history showcommand and see the output shown in the exhibit.
The customer confirms that the AutoSupport settings are correct.
Which two actions will solve this issue? (Choose two.)
- A. The customer needs to enable AutoSupport for both nodes.
- B. The customer needs to white-list the two nodes on their mail server.
- C. The customer needs to exclude the two nodes from the attachment-size limitation.
- D. The customer needs to change the transport protocol to HTTP.
Answer: A,B
NEW QUESTION # 34
Click the Exhibit button.
You are reviewing the setup of a recently installed FAS9000 switched cluster. As shown in the exhibit, the cluster interconnects are connected to a pair of Cisco Nexus 3132Q-V 40 Gb ports.
For a high availability, which ports should swap Ethernet cables?
- A. Swap node2:e4a and node2:e8a.
- B. Swap node1:e8a and node2:e4a.
- C. Swap node1:e4a and node1:e8a.
- D. Swap node1:e4a and node2:e4b.
Answer: B
NEW QUESTION # 35
You must replace a FAS2750 switchless cluster with an AFF A220 switchless cluster for a customer. The customer requires that you transfer the data from the FAS2750 cluster to the AFF A220.
In this scenario, which two methods would you use to migrate the customer's data? (Choose two.)
- A. Provide cluster switches and build a 4-node cluster, then use the vol move command.
- B. Remove all of the HDD drives from the FAS cluster and install them into the AFF cluster.
- C. Install SAS cables between the two clusters and use the vol move command.
- D. Establish an SVM-DR relationship between the two clusters and activate the destination SVM.
Answer: A,C
NEW QUESTION # 36
You have installed a new 2-node FAS9000 cluster with two external shelves. You want to make sure that each node has two paths to each disk in the shelves.
How do you verify your configuration?
- A. Use the storage disk option show command.
- B. Use the storage show disk -p command.
- C. Use the sysconfig command.
- D. Use the disk show -fields initiator command.
Answer: D
NEW QUESTION # 37
You are setting up a new AFF A400 that will serve iSCSI LUNs. You will have four iSCSI SVMs that each need to connect to an Internet Storage Name Service (iSNS) for discovery and management purposes.
In this scenario, which network interface is needed for each SVM to register with the name service?
- A. node management LIF
- B. SVM management LIF
- C. SVM data LIF
- D. intercluster LIF
Answer: B
Explanation:
https://docs.netapp.com/ontap-9/topic/com.netapp.doc.dot-cm-sanag/GUID-E0C83978-2139-48C5-8C2B-80F4A385583E.html
NEW QUESTION # 38
Click the Exhibit button.
Referring to the exhibit, what information is forwarded to syslog after you enter the scripted install commands? (Choose two.)
- A. AutoSupport messages
- B. EMS messages
- C. SNMP traps
- D. command history
Answer: A,D
NEW QUESTION # 39
......
NS0-183 [Dec-2023] Newly Released] NS0-183 Exam Questions For You To Pass: https://actual4test.torrentvce.com/NS0-183-valid-vce-collection.html