Accurate Hot Selling 350-501 Exam Dumps 2024 Newly Released
Get 100% Authentic Cisco 350-501 Dumps with Correct Answers
NEW QUESTION # 46
Refer to the exhibit.
An engineer is updating this network to meet these conditions:
* Area 10 will receive inter-area routes and support mutual redistribution of external routes with the extranet.
* The ::/0 route is prohibited in Area 10.
* Area 11 will receive only the ::/0 route from the ABR.
* External route redistribution is not supported in Area 11.
* The ABR in Area 11 will advertise no interarea routes.
Which two configurations must be performed to meet the requirements? (Choose two.)
- A. Configure area 11 as nssa no-summary on R7 and as nssa on XR31.
- B. Configure area 10 as nssa on R9 and XR32.
- C. Configure area 11 as nssa default-information-originate on R7 and as nssa on XR31.
- D. Configure area 10 as stub on R9 and XR32.
- E. Configure area 11 as stub no-summary on R7 and as stub on XR31.
Answer: B,E
NEW QUESTION # 47
Refer to the exhibit:
A network engineer is implementing a BGP routing policy.
Which effect of this configuration is true?
- A. All traffic that matches acl10 is allowed without any change to its local-preference
- B. All traffic is assigned a local-preference of 30O regardless of its destination
- C. If traffic matches acl10, it is allowed and its local-preference is set to 300
- D. All traffic that matches acl10 is dropped without any change to its local-preference
Answer: A
NEW QUESTION # 48 
Refer to the exhibit. A network engineer is implementing a standard customer route-policy on router ASBR1 with these requirements:
* It must accept only customer-assigned prefixes.
* It must preserve customer-advertised BGP communities.
* It must set the local-preference to 110 for all prefixes.
* It must attach the ORIGINATION-PE and LOCAL-CITY communities to all accepted prefixes.
Which route policy must the engineer implement on ASBR1 to satisfy the requirements?
- A.
- B.
- C.
- D.
Answer: B
Explanation:
Section: Networking
NEW QUESTION # 49
Which statement about the BFD-BGP Multihop Client Support and cBit feature is true?
- A. BFD cBit identifies VPNv4 and VPVn6 in a multihomed to avoid purging prefixes in an event of link failure when a backup link exists and is installed already in the RIB/FIB.
- B. BFD cBit feature replaces the BGP graceful restart and the BGP fast-failover features by keeping stale routers in the RIB when a failure occurs on the control plane.
- C. The cBit in BFD determines if the BFD session failure is independent or dependent of the control plane.
- D. BFD cBit improves the BGP convergence and response time to adjacency changes with BGP neighbors; in any event of adjacency changes, the session is deactivated in the next BGP scanning interval.
Answer: C
NEW QUESTION # 50
After a possible security breach, the network administrator of an ISP must verify the times that several different users logged into the network. Which command must the administrator enter to display the login time of each user that activated a session?
- A. show netconf-yang sessions detail
- B. show platform software yang-management process
- C. show netconf-yang sessions
- D. show netconf-yang datastores
Answer: A
Explanation:
Explanation
https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/prog/configuration/167/b_167_programmability_cg/configuri
NEW QUESTION # 51
Refer to the exhibit.
Refer to the exhibit. An engineer is configuring IS-IS on ISP network. Which IS-IS configuration must an engineer implement on router AGG1 so that it establishes connectivity to router AGG6 via the BB3 core router?
- A. router isis 100
metric-style narrow
interface GigabitEthernet 3
isis metric 10 level-2 - B. router isis 100
metric-style wide
interface GigabitEthernet 3
isis metric 1500 level-2 - C. router isis 100
metric-style wide
interface GigabitEthernet 3
isis metric 1500 level-1 - D. router isis 100
metric-style narrow
interface GigabitEthernet 3
isis metric 10 level-1
Answer: D
NEW QUESTION # 52
Refer to the exhibit.
Refer to the exhibit. Over the last few months. ISP A has doubled Its user base. The IT Director asked the engineering team to monitor memory consumption and buffer statistics on all P and PE devices In the MPLS core. Most devices have CPU usage of 70% or more, so the solution must be targeted and secure. Which two commands must the engineering team implement on P and PE devices to meet these requirements? (Choose two.)
- A. snmp-server host 192.168.101.1 version 2c community1 memory
- B. snmp-server host 192.168.101.1 version 3 auth community1 memory
- C. snmp-server enable traps memory bufferpeak
- D. snmp-server enable snmp-traps community1 bufferpeak
- E. snmp-server host 192.168.101.1 version 1 community1 auth memory
Answer: B,C
NEW QUESTION # 53
Refer to the exhibit:
This configuration is being applied on an IOS XR router.
Which statement about this configuration is true?
- A. It is used to identify MIB entries and has a list of YANG models
- B. It is used to identify traps for SNMP polling
- C. It is used to create a sensor-group and has a list of YANG models for streaming
- D. It is used to create a subscription to specify the streaming interval
Answer: C
NEW QUESTION # 54
A customer site is being connected to a Frame Relay network via a T1 link. The customer has a contract for 512 kbps service with a Tc value of 125 ms. Under peak line conditions, customer traffic can reach four times the contracted speed. Which QoS configuration must the service provider implement to limit the customer to the contracted values?
- A. Option D
- B. Option C
- C. Option B
- D. Option A
Answer: D
NEW QUESTION # 55
Refer to me exhibit.
A network operator recently configured BGP FlowSpec for me internal IT network What will be inferred from the configuration deployed on me network?
- A. The policy is configured locally on CSR1 and currently has no active traffic
- B. The policy is warned via BC FlowSpec aid has active traffic
- C. The policy is configured locally on CSRl and drops all traffic for TCP ports 80 and 443
- D. The policy is learned via BGP FlowSpec and drops all traffic for TCP ports 80 and 443
Answer: C
NEW QUESTION # 56
Refer to the exhibit.
Refer to the exhibit. An ISP provides shared VoIP Extranet services to a customer in VRF-100 with these settings:
The VoIP services are hosted in the 198.19.100.0/24 space.
The customer has been assigned the 198.18.1.0/29 IP address block.
VRF-100 is assigned import and export route target 65010:100.
Which configuration must the engineer apply to PE-1 to provision VRF-100 and provide access to the shared services?
- A. vrf definition VRF-100
rd 172.17.255.1:100
!
address-family ipv4
export map VRF-100-EXPORT
import map VRF-100-IMPORT
exit-address-family
!
route-map VRF-100-EXPORT permit 10
match ip address prefix-list VRF-100-ALLOWED-EXPORT
set extcommunity rt 65010:100 65010:2999
route-map VRF-100-EXPORT permit 20
set extcommunity rt 65010:100
!
route-map VRF-100-IMPORT permit 10
match extcommunity VRF-100-RT SHARED-SERVICES
!
ip extcommunity-list standard SHARED-SERVICES permit rt 65010:1999
ip extcommunity-list standard VRF-100-RT permit rt 65010:100
ip prefix-list VRF-100-ALLOWED-EXPORT seq 5 permit 198.18.1.0/29 - B. vrf definition VRF-100
rd 172.17.255.1:100
!
address-family ipv4
route-target export 65010:100
route-target export 65010:1999
route-target import 65010:100
route-target import 65010:2999
exit-address-family - C. vrf definition VRF-100
rd 172.17.255.1:100
!
address-family ipv4
export map VRF-100-EXPORT
route-target import 65010:100
route-target import 65010:2999
exit-address-family
!
route-map VRF-100-EXPORT permit 10
match ip address prefix-list VRF-100-ALLOWED-EXPORT
set extcommunity rt 65010:100 65010:1999
route-map VRF-100-EXPORT permit 20
set extcommunity rt 65010:100
!
ip prefix-list VRF-100-ALLOWED-EXPORT seq 5 permit 198.18.1.0/29 - D. vrf definition VRF-100
rd 172.17.255.1:100
!
address-family ipv4
export map VRF-100-EXPORT
route-target import 65010:100
route-target import 65010:1999
exit address-family
!
route-map VRF-100-EXPORT permit 10
match ip address prefix-list VRF-100-ALLOWED-EXPORT
set extcommunity rt 65010:100 65010:2999
route-map VRF-100-EXPORT permit 20
set extcommunity r 65010:100
!
ip prefix-list VRF-100-ALLOWED-EXPORT seq 5 permit 198.18.1.0/29
Answer: B
NEW QUESTION # 57
Refer to me exhibit. A network engineer notices PE-21 convergence degradation due to the growing LSDB size of Level 2 areas in the network The engineer decides to migrate router PE-21 from an inter-area design to an intra-area implementation, inter-area routing must De accomplished via an ATT-bit set by the Level 1/Level 2 router. Which configuration must the engineer implement on PE-21 to complete the migrate?
- A. Option C
- B. Option B
- C. Option D
- D. Option A
Answer: C
NEW QUESTION # 58
Refer to the exhibit.
A network engineer must implement SNMPv3 on a Cisco IOS XR router running BGP. The engineer configures SNMPv3 to use SHA for authentication and AES for privacy on the routers, which are in a different data center in the same exchange as other routers. The engineer must also verify the associated MIB view family name, storage type, and status. Which set of actions meets these requirements?
- A. Add configuration snmp-server user AuthUser group2 remote 10.1.1.1 v3 auth sha and use show snmp mib to verify the configuration.
- B. Add configuration snmp-server user UserJustMe GrpMonitoring v3 auth sha AuthPass1 priv 3des 128 PrivPass2 and use show snmp interface to verify the configuration.
- C. Add configuration snmp-server user AuthUser group2 remote 10.1.1.1 v3 auth sha and use show snmp engineid to verify the configuration.
- D. Add configuration snmp-server user UserJustMe GrpMonitoring v3 auth sha AuthPass1 priv aes 128 PrivPass2 and use show snmp view to verify the configuration.
Answer: D
NEW QUESTION # 59
Drag and drop the OSPF and IS-IS Cisco MPLS TE extensions from the left to their functional descriptions on the right.
Answer:
Explanation:
NEW QUESTION # 60
Refer to the exhibit:
An engineer wants to authenticate the OSPF neighbor between PEA and PE-B using MD5.
Which command on PE-B successfully completes the configuration?
A)
B)
C)
D)
- A. Option D
- B. Option C
- C. Option B
- D. Option A
Answer: D
NEW QUESTION # 61
Refer to the exhibit.
A network engineer Is implementing OSPF multiare
a. Which command on interface G0/1 resolves adjacency Issues in the new area?
- A. Ip ospf network non-broadcast
- B. Ip ospf network polnt-to-multlpoint
- C. Ip ospf network point-to-point
- D. Ip ospf network broadcast
Answer: C
Explanation:
https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/iproute_ospf/configuration/xe-16/iro-xe-16-book/iro-multi-area-adj-xe.html
NEW QUESTION # 62
Refer to the exhibit:
An engineer is preparing to implement data plane security configuration.
Which statement about this configuration is true?
- A. Router 2 is the router receiving the DDoS attack
- B. Router 1 is the trigger router in a RTBH implementation.
- C. Router 1 must be configured with uRPF for the RTBH implementation to be effective.
- D. Router 2 must configure a route to null 0 for network 192 168.1 0/24 for the RTBH implementation to be complete.
Answer: B
NEW QUESTION # 63
Drag and drop the multicast concepts from the left onto the correct descriptions on the right.
Answer:
Explanation:
NEW QUESTION # 64
Refer to the exhibit. Routers P4 and P5 receive the 0.0.0.0/0 route from the ISP via eBGP peering. P4 is the primary Internet gateway router, and P5 is its backup. P5 is already advertising a default route into the OSPF domain. Which configuration must be applied to P4 so that it advertises a default route into OSPF and becomes the primary Internet gateway for the network?
- A. configure terminal
router ospfv3 100
address-family ipv4 unicast
default-information originate metric 40 metric-type 1
end - B. configure terminal
router ospfv3 100
address-family ipv4 unicast
default-information originate always metric 40 metric-type 1
end - C. configure terminal
router ospfv3 100
address-family ipv4 unicast
default-information originate metric 40 metric-type 2
end - D. configure terminal
router ospfv3 100
address-family ipv4 unicast
redistribute bgp 65500 metric 40 metric-type 1
end
Answer: C
NEW QUESTION # 65
A network engineer is implementing BFD configuration changes on a customer's equipment. How is the bfd interval configuration on the interface disconnected?
- A. The status of the interface changes.
- B. It is automatically disconnected when the BFD main interface is removed.
- C. It is automatically disconnected when the BFD-configured subinterface is removed.
- D. The IPv4 or IPv6 address configuration on the interface changes.
Answer: B
NEW QUESTION # 66
Which BGP attribute is used first when determining the best path?
- A. local preference
- B. AS path
- C. weight
- D. origin
Answer: C
Explanation:
Section: Networking
NEW QUESTION # 67
Refer to the exhibit:
Router 1 was experiencing a DDoS attack that was traced to interface gjgabitethernet0/1.
Which statement about this configuration is true?
- A. Router 1 accepts all traffic that ingresses and egresses interface gigabitethernet0/1
- B. Router 1 accepts source addresses on interface gigabitethemet0/1 that are private addresses
- C. Router 1 accepts source addresses that have a match in the FIB that indicates it is reachable through a real interface
- D. Router 1 drops all traffic that ingresses interface gigabitethernet0/1 that has a FIB entry that exits a different interface
Answer: C
NEW QUESTION # 68
Refer to the exhibit.
Refer to the exhibit. Router BRDR-1 is configured to receive the 0.0.0.0/0 and 172.17.1.0/24 network via BGP and advertise then into OSPF area 0. An engineer has noticed that the OSPF domain is receiving only the 172.17.1.0/24 route and default router 0.0.0.0/0 is still missing. Which configuration must an engineer apply to resolve this problem?
- A. Option C
- B. Option B
- C. Option D
- D. Option A
Answer: C
NEW QUESTION # 69
Refer to the exhibit.
An engineer has started to configure a router for secure remote access as shown. All users who require network access need to be authenticated by the SSH Protocol.Which two actions must the engineer implement to complete the SSH configuration? (Choose two.)
- A. Configure a password under the vty lines.
- B. Configure ACL 100 to permit access to port 22.
- C. Configure service password encryption.
- D. Configure an IP domain name.
- E. Configure crypto keys
Answer: D,E
NEW QUESTION # 70
Refer to the exhibit:
When implementing an LDP protocol, an engineer experienced an issue between two directly connected routers and noticed that no LDP neighbor exists for 1.1.1.1.
Which factor should be the reason for this situation?
- A. LDP needs to be enabled on the R2 physical interface
- B. LDP needs to be enabled on the R2 loopback interface
- C. R2 does not see any hellos from R1
- D. R2 sees the wrong type of hellos from R1
Answer: C
NEW QUESTION # 71
......
Related Certifications
- CCNP Service Provider
Cisco CCNP Service Provider proves your capability to implement service provider solutions. Achieving this certificate requires meticulous mastery of 350-501 exam concepts in addition to passing the concentration test of your liking. That being said, the full list of the concentration options associated with the CCNP Service Provider certification includes the following: Cisco 300-510 Implementing Cisco Service Provider Advanced Routing Solutions (SPRI), Cisco 300-515: Implementing Cisco Service Provider VPN Services (SPVI), Cisco 300-535: Implementing Automation for Cisco Service Provider Solutions (SPAUTO).
- Cisco Certified Specialist – Service Provider Core
Cisco Certified Specialist – Service Provider Core is a creation of the new Cisco curriculum which states that every professional-level exam now earns the candidates a Specialist title alongside the accreditation they are going to obtain. In a nutshell, this is a deserved recognition for your accomplishments at the professional level regardless of your further path.
- CCIE Service Provider
Cisco CCIE Service Provider lies at the pinnacle of the Cisco Service Provider certification track and is exactly the step to make after attaining the CCNP Service Provider certificate. It confirms one's expert-level mastery of Service Provider technologies. To qualify for it, you must pass a combination of two exams a core 350-501 test that focuses on the fundamentals of the field and a hands-on lab exam that checks the mastery of the service provider solutions through a practical environment. The lab exam, in this case, is CCIE Service Provider v5.0.
Cisco 350-501 exam requires a deep understanding of service provider networks and the technologies used to operate them. Candidates are expected to have experience in configuring and troubleshooting network protocols, as well as knowledge of network automation tools. 350-501 exam is ideal for network engineers, network administrators, and network architects who work in service provider environments. Passing 350-501 exam will not only validate the candidate's skills but also enhance their career prospects by opening up opportunities for higher-level roles in the service provider industry.
Dumps of 350-501 Cover all the requirements of the Real Exam: https://actual4test.torrentvce.com/350-501-valid-vce-collection.html